Exactly How to Install a Bathtub
Exactly How to Install a Bathtub
Blog Article
Almost everyone maintains their private theory in relation to How to Install a Bathtub Yourself.
Installing a bathtub isn't specifically brain surgery, yet it does need solid plumbing, carpentry, and also often, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a reasonably challenging project. If the old bathtub is conveniently easily accessible, the job can move speedily; if you need to open up a wall to get rid of the old bathtub as well as position the brand-new tub, the task is much harder. In either case, the project is within a residence handyman's skills, although you will require an assistant to move out the old bathtub as well as set in the brand-new one. Make certain you have qualified on your own for the task and fit attempting it. Rather than working with a specialist to take over a halfway-completed task, it is much better to take into consideration utilizing one before you begin. Opportunities are you may require an expert plumber to make tube links.
This short article will certainly help you mount a new tub in your bathroom if you have actually currently purchased a brand-new tub as well as don't need to transform the arrangement of your previous water pipes.
Your devices and also material list should make up the following:
Preparing for the Setup
To start with, the supporting framework provided with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps system to stop strain on the tub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be suited its final setting.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly problematic due to the restricted gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly come from the pipes. When the supply pipelines have been removed, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for setting. The wood boards are practical in uniformly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four small factors.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the spirit level checks out level.
To set up taps, fit the bottom of the furthest versatile tap connector to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water and also inspect all joints as well as new pipework for leaks and tighten them if necessary. Fill the bathtub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling and sealing around the bath tub needs to wait till the tub has been used at the very least when as this will resolve it right into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the faucet and the sink. Safeguard the tap in position with the producer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap connectors. The former type must be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a rigid seal, triggering the water to pass through the wall between the bathroom and the tiling, resulting in difficulties with dampness as well as feasible leakages to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealer can fracture rather very early if you do not think about this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the market. It is advisable to fit the floor tiles making use of waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Hopefully you enjoyed reading our excerpt about How to Install a Bathtub Yourself. Many thanks for taking a few minutes to read our short article. Appreciated our piece? Please share it. Let somebody else find it. Thanks a lot for your time spent reading it.
Click Here To Find Out More Report this page